|
|
|
Who's Online
There currently are 6043 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
- Very good scan quality, PERFECT!
- Sehr gute scan Qualitaet, empfehlenswert!
Wolfgang Sundhaus
 ;
Good site, works ok and you get what you order, no problems experienced, got my manual within a day. A++++
;
Original well scanned manual. Got the job done. Microwave problem found & corrected. For $5 and a new magnitron from ebay, it was a cheap and good the first shot fix. Electrical schematics allowed me to mage sure every thing else was ok before cutting and order for parts. Hard to live without.
;
I was very skeptical of this website, I have never downloaded manuals before. I put it on the AMEX and payed through Paypal to ensure protection. I got the manual exactly as described and now I can replace the filter capacitor for this amp. Great Price, others selling for 12.99 or more and this is the same manual. I will search out this website for other manuals. Thank you
;
Manual was reasonably easy to follow. I am not an engineer or know much about electronics but with the manuals help I was able to figure out the problem, identify the part required for the repair. Replacement part cost around $30. Whilst replacing the part I was telling myself, "this aint gonna work cos it seems far too easy". Took about 15 minutes to do and my plasma TV works a treat. Would never have been able to do this without the service manual.
CHAPTER 2
2. Automatic power control of laser diode The laser driver IC conducts the automatic power control (APC) of the laser diode so that the laser diode emits a beam of constant intensity. The APC is conducted prior to the image formation (Initial APC) and between lines (between line APC). When the CNTRL0 signal and CNTRL1 signal input to the laser driver IC from the CPU are �L� and �H� respectively, the sample hold circuit in the laser driver IC enters the sample mode (mode in which the APC is performed). At the same time, the laser diode (LD) emits the laser beam forcibly. The intensity of the laser beam emitted from the laser diode is detected by the photo diode (PD) and fed back to the sample hold circuit via the current/voltage converting circuit and differential amplifier. The laser driver IC controls the output current of the drive circuit to make the fed back laser intensity become equal to the target laser intensity set in the IC. When the CNTRL0 signal and CNTRL1 signal become �H�, the laser diode is turned OFF forcibly and the sample hold circuit enters the hold mode. The laser driver IC converts the controlled laser intensity to voltage and stores it in the C804. 3. Horizontal sync control The CPU generates the UNBLANKING signal based on the BD INPUT signal (/BDI) sent from the BD PCB in the laser/scanner unit. During unblanking period, the CPU controls the LASER CONTROL signal to emit laser forcibly. There is a small fixed mirror (BD mirror) on the scanning start position in the optical path. The laser beam is reflected by the BD mirror and sent to the BD PCB in the laser/scanner unit. The BD PCB generates the BD INPUT signal (/BDI) based on the detected laser beam and sends the signal to the CPU. The CPU generates HORIZONTAL SYNC signal (/BD) based on the /BDI and starts sending the signal to the video controller when it detects that the picked up paper has reached the specified position. 4. Image masking control The CPU performs the image masking control in order to prevent laser beam emission in the non-image area other than the unblanking period. The laser beam emission enable period of the laser diode is controlled by masking the /VDO and VDO with the LASER CONTROL signals (CNTRL0, CNTRL1) in the logic circuit in the laser driver IC. The CPU sets the CNTRL0 and CNTRL1 to �H� in the image mask area other than the unblanking period so that the laser diode will not be turned ON/OFF when the /VDO and VDO are sent to the laser driver IC from the video controller. In image unmasking area, the laser driver IC turns ON/OFF the laser diode based on the /VDO and VDO by setting CNTRL0 to �H� and CNTRL1 to �L.�
2 - 20
|
|
|
> |
|
